THE PRODUCT DEEPCAST That's it. You can also work well with synthetic resin beyond classic painting grounds: Cast large casting heights, high volumes, unusual shapes and 3D molds. DEEPCAST ??is a two part resin and one of the highest quality products on the market. The application is easy and safe. With DEEPCAST ??you will create impressive objects. It can. When mixing its two individual components, DEEPCAST ??becomes a hard and glass-like cast. It also offers the best possible protection against yellowing. So-called UV stabilizers ensure this: Our products contain a UV absorber and HALS (Hindered Amine Light Stabilizer). That's what it's for. We developed DEEPCAST ??specifically to fill cavities. This makes it perfect for making a river table, for example. Pour up to twelve liters in one go with DEEPCAST ??and achieve a layer height of 5 cm and more. Particularities. DEEPCAST ??has a long curing time, which means it will not shrink as it cures - an important consideration for crafts and artists. The reason for this is the low heat development. With DEEPCAST, the exothermic reaction when resin and hardener are combined is significantly weaker than with other resin systems. Measuring, mixing and processing DEEPCAST 1. DEEPCAST ??resin and hardener are mixed by volume 2:1. Place the two components in a mixing bowl. 2. Stir the measured amount in the mixing bowl. Use a stir stick for this. Stir slowly and thoroughly for 3-5 minutes; also on the bottom and the edges of the mixing vessel. 3. Your mix is ??ready and you now have 25 hours* to process the resin. After that it becomes too thick and begins to harden. 4. You have previously prepared your form accordingly. Now pour the resin mixture into the mold. 5. Protect your work from dust or other foreign objects by working in an environment that is as dust-free as possible. Cover it when it's done. You should pay attention to this: Although our resins are formulated with the most advanced and safest epoxy chemistry available, you should handle all epoxy resins responsibly and be proactive about your safety: •Always wear nitrile gloves. •When sanding cured resin, wear a dust mask, and better yet, wear safety goggles. •It is advisable to work in a well-ventilated room. •Avoid skin contact (if resin gets on skin, wash with plenty of soap and water). •DO NOT eat, drink or smoke while working. •If eyes get dirty, wash with plenty of water for 15 minutes and seek medical attention immediately. •Adding inks/varnishes/mica powder/glitter to epoxy changes its properties and may reduce its non-toxicity. If using alcohol inks, DO NOT use a flame to remove bubbles as alcohol is flammable. DEEPCAST ??does not contain a drying accelerator. Therefore, both the processing and the curing time for this resin are significantly longer than for others. You can find more technical information about the Eli-Chem-Resin DEEPCAST ??in our overview table. DEEPCAST ??is available in the following sizes: 1.5 l, 3 l, 7.5 l, 37.5 l

THE RESI-TINT MAX PEARLISH PIGMENT PASTES IN 14 COLOURS That's them. With our high-quality resi-TINT MAX pearlescent pigment pastes in 14 different colors, you can conjure up great visual effects with resin on your artwork. The cells that you can create with the resi-TINT MAX pearlescent pigment pastes are fascinating. With their chemical composition and consistency, they ensure rich color effects and a good connection with the resin on your artwork. In addition, they offer you a great advantage for working with cell effects. In addition, the resi-TINT MAX pearlescent pigment pastes offer a pearlescent shimmer that gives your work a unique play of colors. To make the cells even bigger and more unique, you can also use resi-BLAST. Decorate your surface with it and create great cell structures and color effects with your heat gun. Particularities. • Pearlescent pre-polymer pigment for rich and shimmering colors. • High viscosity. • Intense, opaque, shimmering and even colors. • Waterproof pigments. • Excellent lightfastness. • Low consumption due to high concentration. • Compatible with all our resin Systems.

THE RESI-TINT MAX PIGMENT PASTES IN 33 COLORS That's them. With our high-quality resi-TINT MAX pigment pastes in 33 different colors you can conjure up great optical effects with resin on your artwork. The cells that you can create with the resi-TINT MAX pigment pastes are fascinating. With their chemical composition and consistency, they ensure rich color effects and a good connection with the resin on your artwork. In addition, they offer you a great advantage for working with cell effects. To make the cells even bigger and more unique, you can also use resi-BLAST. Decorate your surface with it and create great cell structures and color effects with your heat gun. Particularities. • High viscosity. • Intense, opaque and even colors. • Waterproof pigments. • Excellent lightfastness. • Low consumption due to high concentration. • Compatible with all our resin Systems.

TOPCOAT 2-1: the scratch-resistant epoxy resin for clear coatings - and much more TOPCOAT 2-1 is a synthetic resin consisting of two components: resin and hardener. After mixing the two components, you get a crystal-clear and extremely hard coating. It not only offers you protection against scratches, but also against yellowing. TOPCOAT 2-1 contains very good UV protection: absorbers and HALS (Hindered Amine Light Stabilisers).   Possible applications of TOPCOAT 2-1 synthetic resin TOPCOAT 2-1 is perfect for sealing surfaces. How does it work? Simply coat your artwork or another surface such as tables or counters with a layer of TOPCOAT 2-1 - and you're done. You can also use TOPCOAT 2-1 for other artistic applications. Of course, it can be quickly dyed to your desired colours using suitable colourants. We know artists, who use it to mould the most amazing coasters. Trays can be designed just as easily. With TOPCOAT 2-1, you can achieve a layer up to 25 mm high in a single step. Sufficiently high even for embedding flat objects. Special features of the TOPCOAT 2-1 resin TOPCOAT 2-1 has a low viscosity and is therefore very fluid. This makes coating with this synthetic resin easy. This epoxy resin also allows you to work almost bubble-free. Important: The resin is purple in liquid form due to the UV protection it contains. However, it hardens to a clear colour, we promise you that.   Application TOPCOAT 2-1 for a clear coating Step 1: Pour the resin and hardener into a suitable mixing cup. Mix TOPCOAT 2-1 by volume 2:1. Step 2: Then mix the two components thoroughly. Stir slowly and carefully with a plastic spatula. Pay attention to the base and rim of your mixing cup. You will be done after 3 to 5 minutes, unless you are mixing a huge amount. In this case, of course, stir for longer. Step 3: You now have a generous 60-80 minutes to process TOPCOAT 2-1. The resin will then start to harden. Step 4: If you have not yet prepared your work or object for the coating, you should do so now. It must be dedusted and degreased. It should also lie flat so that you can achieve an even coating. TOPCOAT 2-1 is self-levelling. Feel free to use a spatula if you want to spread everything a little faster. Step 5: If small bubbles do get into the surface, you can easily remove them with a hot air dryer or crème brûlée burner. To do this, swivel your tool about ten centimetres above the resin surface. Step 6: Now allow your coating to harden. Protect your object from dust or other foreign objects. Step 7: You can easily wipe the hardened surface with a damp cloth to clean it later. Have you already worked with a different epoxy resin on your work and want to apply a final coat of TOPCOAT 2-1? Please wait until the previous surface has hardened, i.e. 24 hours. Then it is ready for the final coat.   You should pay attention to this! Although our resins are formulated with the most modern and safest epoxy chemicals available, you should handle all epoxy resins responsibly and proactively ensure your safety: -Always wear nitrile gloves -When sanding cured resin, wear a dust mask and, even better, safety goggles -It is advisable to work in a well-ventilated area and wear a respirator mask -Avoid skin contact (if resin gets on the skin, wash with plenty of soap and water) -DO NOT eat, drink or smoke while working -If eyes are contaminated, wash with plenty of water for 15 minutes and seek medical attention immediately Adding inks/paints/mica powder/glitter to epoxy resin will alter its properties and may reduce its non-toxicity. If you use alcohol ink, DO NOT use a flame to remove bubbles as alcohol is flammable Further technical information on Eli-Chem-Resin TOPCOAT 2-1 can be found in our overview table. TOPCOAT 2-1 is available in the following container sizes: 1.5 kg, 3 kg, 7.5 kg, 15 kg

THE PRODUCT TOTALCAST That's it. TOTALCAST is a crystal clear, ASTM certified, two part resin. It is well suited for embellishing artworks and embedding objects and is among the highest quality resins on the international market. Working with TOTALCAST means: easy and safe application - impressive and high-gloss results. It can. TOTALCAST becomes a hard and glassy varnish when its two individual components are mixed together. It also offers the best possible protection against yellowing. This is ensured by so-called UV stabilizers: Our products contain a UV absorber and HALS (Hindered Amine Light Stabilizer), which provide maximum protection against yellowing. That's what it's for. TOTALCAST is particularly useful when you want to coat or embed (cast) something. This is due to its unique clarity and transparency. Use this high-quality resin as a coating, sealing and finishing for your artwork. For example on photos, prints, canvas, wood, MDF, glass, Plexiglas, concrete or metal. TOTALCAST is also the right resin for you for making jewelry and embedding objects. Particularities. TOTALCAST has a rather short processing time of up to 20 minutes. This has the advantage that your objects dry faster and are therefore less susceptible to dust or other external influences. Measure, mix and process TOTALCAST 1.) TOTALCAST resin and hardener are mixed by volume 1:1. Place the two components in a suitable mixing cup. 2.) Stir the measured amount in the mixing cup. Use a plastic spatula for this. Stir slowly and thoroughly for 3-5 minutes; also on the bottom and edges of the mixing cup. 3.) Your mix is ??ready and you now have 15-20 minutes to process the resin. After that it becomes too thick and begins to harden. 4.) You have prepared your painting surface beforehand, which means: it has been dusted off, degreased and is lying flat on your work surface. Coating: Now pour the synthetic resin mixture onto the painting surface. Resin is self-leveling and will spread itself over a smooth, flat surface. but you are welcome to help with a spatula. Pour in: your painting surface is prepared and also has a frame so that the resin does not flow away. Pour resin onto the canvas; a layer structure is possible in several layers. Depending on the volume, note the maximum layer thickness of 1-2 cm. As soon as the first layer is bone dry (after about 4-5 hours) you can pour the next layer. The individual casting steps are not visible from above. A slight optical thermocline can only be seen in the planes when viewed from the side. 5.) TOTALCAST is a high-quality product that produces only small bubbles, if any. If bubbles appear, simply remove them with the heat of a Bunsen burner or a heat gun. To do this, move about 10 cm away from the resin surface in swinging movements. 6.) Protect your work from dust or other foreign objects by working in an environment that is as dust-free as possible. Cover it when it's done. 7.) The best way to clean the hardened surface is with a damp Cloth. You should pay attention to this: Although our resins are formulated with the most advanced and safest epoxy chemistry available, you should handle all epoxy resins responsibly and be proactive about your safety: • Always wear nitrile gloves. • When sanding cured resin, wear a dust mask, and better yet, wear safety goggles. • It is advisable to work in a well-ventilated area and to wear a Respirator. • Avoid skin contact (if resin gets on skin, wash with plenty of soap and water). • DO NOT eat, drink or smoke while working. • If eyes get dirty, wash with plenty of water for 15 minutes and seek medical attention immediately. • Adding inks/varnishes/mica powder/glitter to epoxy changes its properties and may reduce its non-toxicity. If using alcohol inks, DO NOT use a flame to remove bubbles as alcohol is flammable. You can find more technical information about the Eli-Chem-Resin TOTALCAST in our overview table. TOTALCAST is available in the following sizes: 500 g, 2 kg, 4 kg, 10 kg